Difference between revisions of "SGI Origin 350"

From Nekochan
Jump to: navigation, search
(Expanding the Power & Cooling section)
m (Slight update on the use of Vantec fans in Origin 350s.)
Line 71: Line 71:
 
|-
 
|-
 
|}
 
|}
# These are variable-speed fans based on a built-in temperature sensor. [http://forums.nekochan.net/memberlist.php?mode=viewprofile&u=543 recondas] reported that one fan in his Origin 350 had to be replaced with a fixed-speed fan to avoid environmental monitoring warnings.
+
# These are variable-speed fans based on a built-in temperature sensor. They are not intended as replacements for any of the OEM fans, they were installed to provide supplemental cooling to [http://forums.nekochan.net/viewtopic.php?f=14&t=16725055#p7338648 Origin 350 systems that have had Odyssey graphics boards added]. [http://forums.nekochan.net/memberlist.php?mode=viewprofile&u=543 recondas] reported that one fan in a 'graphics-board added' Origin 350 had to be replaced with a fixed-speed fan to avoid environmental monitoring warnings.
  
  

Revision as of 04:31, 7 May 2012

SGI Origin 350 technical server.
SGI Origin 350, 8-brick config
SGI Origin 350, 8-brick config

The SGI Origin 350 computer system uses MIPS-based processors. Current models run at 600-1000MHz, with dual or quad CPU configurations available.

The Origin 350 is a member of the Chimera family (IP53), which includes Origin 350, Onyx 350, and the Tezro Rackmount. All three systems have the same basic hardware - the Origin 350 (Chimera Server) with a VPro card becomes the Onyx 350 (ChiBlade), and the ChiBlade can be configured into a Chimera Rackmount Workstation (Tezro Rack) using the L1's make rmws 1 command. The Chimera Rackmount Workstation cannot accept remote serial numbers, and therefore cannot be connected via NUMALink.

Each CPU brick has four PCI slots across two PCI busses. Each CPU brick also has a Fuel-style XIO slot, which can accept a DMediaPro DM3 card or a VPro graphics card. The first CPU brick in a system has a single PCI slot holding an IO9 BaseIO card with SCSI interfaces for two internal disks, an external SCSI port, audio I/O and a twisted pair Ethernet connection. Other kinds of bricks are available that are dedicated to disk storage or further PCI slots.


Different Configurations

Base Compute Module - Includes an IO9, a SCA SCSI backplane (for disks), appropriate cables for disk backplane + IDE CDROM and a daughtercard that provides PS/2 keyboard/mouse and four additional serial ports

Expansion Compute Modules - These may or may not include the IO9+backplane, but lacks the daughtercard/keyboard/mouse/extra serial ports

Memory and PCI Expansion (MPX) Modules - Lacks the IO9+backplane and daughtercard/keyboard/mouse/extra serial ports.

A word of caution:

If you manage to get hold of an O350 brick (module), check the back of the unit to verify that it has an IO9 in the lowest PCI/PCI-X slot. Without that you can't use the brick as a standalone system and you're forced to NUMAlink the brick to another brick and thus expanding an existing system. The IO9 BaseIO card is shared with the Tezro so one could still make the system a complete standalone machine, but without the SCSI backplane, disk sleds (and possibly CDROM) you can't boot the system using internal storage so you're forced to use the external SCSI port on the IO9 or use PCI cards for FibreChannel etc. --Ramq 08:50, 2 December 2009 (UTC)

Multiple Bricks

Multiple bricks are co-ordinated at startup time via an L2 Controller which communicates to the bricks via USB ports. The L2 Controller is an external PowerPC Linux unit with console, USB, modem and ethernet ports.

A system consists of up to eight CPU "bricks" (2 rackmount units high each) with up to four CPUs in each brick, giving a maximum of 32 CPUs. CPU bricks are connected together via NUMAlink3 cables going to a central NUMAlink router (or NUMAlink module) which is another 2U rackmounted unit.

Power and Cooling

Power Consumption

These values are measured using a Watt-meter off a standard 230V wall outlet:

L1 Only (machine off):     13W
Brick #1 on, idle:      215W (4x700MHz, 4GB RAM (8x512MB sticks), two SCSI harddrives, IO9 + extra GbE card)
Brick #1 on, load:      250W (4x700MHz, 4GB RAM (8x512MB sticks), two SCSI harddrives, IO9 + extra GbE card)
Brick #2 on, idle:      160W (4x700MHz, 1GB RAM (2x512MB sticks), no harddrives or PCI cards)
Brick #2 on, load:      185W (4x700MHz, 1GB RAM (2x512MB sticks), no harddrives or PCI cards)

Fans

The Origin/Onyx 350 comes with reasonably quiet fans (by server standards), but it may still be necessary to replace a failed unit. This table will try to collect information about suitable replacement fans.

Fan Bearing Type Air Flow Speed Noise MTBF Availability Confirmed? Reference Forum Thread Notes
Vantec TF6025 Thermoflow 2 ball bearing 9.9 - 24.2 CFM 1,900 - 4,200 RPM 19 - 33.5 dBA n/a 2012Q2 Yes Vantec USA April 19, 2012 by recondas 1
  1. These are variable-speed fans based on a built-in temperature sensor. They are not intended as replacements for any of the OEM fans, they were installed to provide supplemental cooling to Origin 350 systems that have had Odyssey graphics boards added. recondas reported that one fan in a 'graphics-board added' Origin 350 had to be replaced with a fixed-speed fan to avoid environmental monitoring warnings.


Hard Drive Carriers

Intel-sr2300-drive-sled.jpg

The Origin/Onyx 350, Prism, Altix 350, and Altix 450/4x00 all use the same drive carriers. These are standard parts used by a number of manufacturers, notably Intel's SC5200, SRSH4, SR1300/2300, and SR1400/2400 and Sun's v60x and v65x servers.

The units carry "Assy A65278-00x" on a sticker, where the "-00x" may end in any digit though "-005" seems common. This assembly number can be useful when searching for parts in the Internet. According to SR1300/SR2300 support documents at intel.com, the Intel accessory part number for the drive carrier is FXX2DRVCARBLK, UPC code "7 35858 14621 0" and "MM #" 835853. However note that there is some indication that Intel may recycle these accessory part numbers in the FXX- form between different models.

As of early 2011 these drive sleds are commonly available on eBay for US$10.

Forum Threads About Origin 350 Drive Carriers

External links