Difference between revisions of "Origin2000/Onyx2 Diagnostics: Router LEDs"
m (Using the Origin2000/Onyx2 Router LEDs as a Diagnostic Tool)
Revision as of 06:45, 18 February 2008
Origin2000/Onyx2 Router LEDs
The standard routers in an Origin2000 or Onyx2 (rack mounted) compute module have a series of LEDs on the external bulkhead. At the top of the bulkhead there are three red LEDs that indicate the status of the power supplied to the router. The red LEDs are followed by two columns of LEDs; six green LEDs in the left column and six yellow LEDs in the right column. Origin2000 and Onyx2 rack mounted compute modules have two routers. The router on the left is Router 1, the router on the right is Router 2.
In addition to the standard (full) router, Origin2000 and Onyx2 systems may be equipped with "null" or "star" routers which having differing numbers of LEDs (or none at all), and different diagnostic characteristics. This article deals solely with standard routers, part number 030-0841-003.
CAUTION: Always power the system off and take proper ESD precautions before disconnecting or removing system components.
Diagnosing Power Issues:
The three LEDs located closest to the top of the router bulkhead indicate the status of power supplied to the router:
R - 3.3VDC R - 2.4VDC R - 1.7VDC
If any of the red LEDs are illuminated, there's an issue with the power being supplied to the router. The following sequence can be helpful in isolating the fault:
- Re-seat the router.
- If re-seating the router fails, switch the router with another.
- If the fault follows the router, replace the router.
- If the fault remains with the router slot, try re-seating the power supply.
- If the fault persists, try another power supply.
- If the fault still persists, suspect the system mid-plane.
Diagnosing Link Issues:
On each router board there are two columns of LEDs, six green and six yellow. When illuminated, green indicates a successful link; yellow can indicate a fault or activity. Each vertical pair of green and yellow LEDs indicate the status of the external ports (top set of 3 LEDs) or internal ports (bottom set of 3 LEDs) on the router:
Status G Y - 1 (external port 1) G Y - 2 (external port 2) G Y - 3 (external port 3) G Y - 4 (node 2 on Router 1, node 4 on Router 2) G Y - 5 (node 1 on Router 1, node 3 on Router 2) G Y - 6 (router to router link (Router 1 or 2))
External Router Ports
The first 3 pairs of green and yellow LEDs indicate the status of the external router ports. The external ports on the router boards numbered top to bottom, with 1 at the top and 3 at the bottom. If a CrayLink cable is attached to the port (and to a port on a router in the other compute module), the corresponding green LED should be on. If the green LED isn't on there's an external link failure on that port. (Note: If the yellow LEDs are on prior to IRIX loading, improper CrayLink cable routing is indicated.) You can do some basic troubleshooting by replacing the CrayLink cable - but do not hot swap CrayLink cables.
Note: CrayLink cables are fragile; avoid tight bends (the OEM cable guides provide support and the correct radius where the cables bend to connect the router ports).
Internal Router Ports
The second 3 pairs of green and yellow LEDs indicate the status of the internal router ports. The first two pairs of this set indicate the status of the link between a node board and the router (the internal connections are via the system mid-plane). If a node (processor) board is installed, the corresponding green LED should be on. If not:
- Re-seat the appropriate node board and router.
- If the problem persists, try switching the appropriate node board and/or router board to see if the problem follows the node/router (switch one, check the status, then the other).
- If the problem follows the node or router, replace it.
- If the problem doesn't follow the node or router, suspect the mid-plane.
Internal Router-to-Router Links
The last (sixth) pair of LEDs indicates the status of the connection between Router 1 and Router 2. If two standard routers are installed, the green LEDs should be illuminated on both routers (but only if both are standard 030-0841-003 routers). If a router to router link is not indicated:
- Re-seat the router(s).
- If the problem persists, switch the router with one from another module.
- If the problem is corrected, suspect the router.
- If the problem persists, suspect the system mid-plane.
There are also LEDs on the mid-plane that indicate the status of the router/mid-plane link. Those LEDs are described in the article Diagnostic LEDs on the Origin2000/Onyx2 Midplane